Dacrylate Paints Ltd.

High Performance Coating Solutions

Dacrylate Anti-Graffiti Products
Margard Anti-Graffiti Finish SP Clear

Margard Anti-Graffiti Finish SP Clear

Reference No.: 9-95

A single-pack moisture cured polyurethane typically used as a clear anti-graffiti coating or as a clear finish coat for coloured anti-graffiti coatings.

Conforms to Railtrack Line Specification RT98.

Colours available: Not applicable
Appearance Of Dried Film: Clear Gloss
Semi-Gloss Ref.: 9-106
Matt Ref.: 9-105
Volume Solids: 45%
Dry Film Thickness: Typical 30 microns. Range 25-50 microns
Theoretical Coverage: 15m² per litre at 30 microns (coverage will be considerably reduced when used on porous concrete or brick surfaces)
Drying Time At 20°C: Touch Dry: 4 hours
Film Dry: 6 hours
Overcoat: After overnight drying (flat down lightly if left more than 3 days)
(will vary with temperature, air movements, etc.)
Note: The Margard Anti-Graffiti Finish SP Clear will develop resistance to most types of graffiti after about 48 hours curing at 20°C.
V.O.C.: 510 grms/litre
Packaging: 5 litre, 2.5 litre and 1 litre screw top cans
Shelf Life: 12 months in unopened containers when stored under cover in good storage conditions.
Storage: Under cover with temperature range of 5°C to 32°C.
Surface Preparation: Substrate must be clean and dry. On brickwork, masonry, etc., remove all dirt, dust and friable material.
Application: Clear Anti-Graffiti System
Thin first coat with 30% Dacrylate Thinner R8. Apply by brush only and ensure full penetration into cracks, fissure and rough profiles. (N.B.: On very course substrate or weathered brickwork, two coats of sealer may be advisable.)
After sealing, apply two furter coats of unthinned Margard Anti-Graffiti Finish SP Clear Ref.: 9-95 by brush or roller.
As Clear Top Coat for Coloured Anti-Graffiti Finish
Apply Margard Sealer and Margard Coloured Finish in accordance with Dacrylate recommendations.
Apply one coat of Margard Anti-Graffiti SP Clear Ref.: 9-95 by brush or roller.
Roller Application: A short-pile 'gloss-type' is essential. Apply using a 'full' roller. Avoid excessive 'rolling-out' which will entrain air-bubbles in the film. Any air-bubbles produced can be removed by lightly brushing the surface with a 3" or 4" paint brush immediately after the roller application.
N.B.: In warm and/or windy conditions, up to 5% of Dacrylate Thinner R8 may be added to assist the application characteristics and extend the 'wet-edge' time.
Application Conditions: Temperature: 5°C to 32°C (Margard SP Clear will cure at temperatures below 5°C however drying/curing will be retarded.)
Humidity: Up to 80% RH.
Note: Margard SP Clear should not be applied when dew point or condensation conditions may occur within 4 hours of application. This is a moisture sensitive product, once the container is opened, the material is best used in one application.
Clean-up: Dacrylate Thinner R6
Health and Safety: For more information request relevant Material Safety Datasheet.

 

The above information is general information on the product but without warranty. Since conditions of service and application are beyond our control we cannot accept claims for loss, damage etc., based on this information. Dacrylate will not accept any claim for consequential or incidental damages.

BBA     BCF     ISO 9001     Royal Society of Chemisty     HEA HEMSA     IPL     Business in the Community     PaintCare     Made in Britain     SEDEX - Supplier Ethical Data Exchange