Dacrylate Paints Ltd.

High Performance Coating Solutions

Dacrylate Anti-Graffiti Products
Margard Easyclean AGS

Margard Easyclean AGS

Reference No.: 300-Line

A high solids compliant two-pack polysiloxane finish that is:

Environmentally Friendly: 37gms VOC compared to 510gms in a polyurethane clear lacquer.
Isocyante Free: Less stringent health and safety requirements during spray application.
Extremely Long Life: Typically 25 to 30 years.
Easy Application: Spray, brush or roller.
One Graffiti Remover: Removes most forms of marker pen and aerosol spray paint.
Overcoat Existing Paints: Suitable to be applied over existing sound paint finishes (following compatibility testing).

Typically used for the long-term protection against graffiti for steelwork, architectural cladding, lighting columns, street furniture, play equipment, etc.

Colours available: RAL, BS or any special colour available
Appearance Of Dried Film: Gloss or semi gloss
Volume Solids: 95%
V.O.C.: 37gms per liture
Dry Film Thickness: Typical 75 microns / Range 75-140 microns
Theoretical Coverage: 12.6m² per litre at 75 microns DFT
Drying Time At 20°C: Touch Dry: 2-3 hours
Film Dry: 7-8 hours
Overcoat: Not normally required
(will vary with temeprature, air movements, etc.)
Packaging: 5 litre composite pack
Shelf Life: 2 years or longer in unopened containers when stored under cover in good storage conditions.
Storage: Under cover with temperature range of 5°C to 32°C.
Surface Preparation: Apply over Dacrylate Epidac 2 HB Aluminium Primer Item 115 Ref.: 90-268 (dry film thickness of primer - approximately 75 microns.
Pot Life (at 20°C): 4 hours
Mixing Ratio by Volume: 4: 1
Clean-up: Thinner R29
Health and Safety: For more information request relevant Material Safety Datasheet.
Surface Preparation: Normally applied over a suitably prepared and primed substrate, please contact us for specific recommendations.
Application: Can be applied by airless, air-assisted and conventional spray and brush or roller.
N.B.: For roller application an addition of 15-20% Thinner R29 and 'lay-off' with a brush will be required.
Apply to a wet film thickness of 80 microns to achieve a 75 micron dry film thickness.
Airless spray: Tip size 11 thou / Fan angle 20-40° / Pressure 3500psi
Based on an airless unit with a 64:1 pump ratio.
Air-assisted spray: Tip size 9-11thou / Fan angle 60° / Pressure 2560psi
Based on Wiwa air-assisted unit with a 32:1 pump ratio.
Conventional Spray: Tip size 1.4mm / Pressure 50-60 psi
Based on DeVilbiss GTi spray gun.
Variations in equipment may require an adjustment in settings.
  Application should not be carried out where the humidity levels exceed 80% RH.
Note: Becaause of the high solids content of this product and the 75 microns recommended DFT, the application methods must be capable of applying a continuous accurate wet film thickness of 80 microns.
This may not be achieveable where high pressure equipment is utilised as the application method.
Practical coverage will be dependent on factors such as object to be painted, equipment used and operator techniques, etc., Allow for appropriate loss factors.
Graffiti Resistance: Full anti-graffiti properties will only be achieved after 7 days curing of the system.
Graffiti Removal: For the full removal of most forms of aerosol spray paint and marker pens used Dacrylate Maclean GP Remover Ref.: 150-198.
Thinner: Not normally required, the addition of up to 5% of Thinner R29 is permissible for conventional spray application if required.
Due to the high solids content of this product, low application temperatures have a marked effect on viscosity, it is recommended that the product is maintained at 15-20°C prior to, and during application.

The above information is general information on the product but without warranty. Since conditions of service and application are beyond our control we cannot accept claims for loss, damage etc., based on this information. Dacrylate will not accept any claim for consequential or incidental damages.

BBA     BCF     ISO 9001     Royal Society of Chemisty     HEA HEMSA     IPL     Business in the Community     PaintCare     Made in Britain     SEDEX - Supplier Ethical Data Exchange